View KS0068B_110906.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

KS0068B
16COM/60SEG DRIVER & CONTROLLER FOR DOT MATRIX LCD
INTRODUCTION
100 QFP The KS0068B is a dot matrix LCD driver & controller LSl which is fabricated by low power CMOS technology.
FUNCTION
* Character type dot matrix LCD driver & controller * Internal driver: 16 common and 60 segment signal output. * Display character format; 5
7 dots + cursor, 5
10 dots + cursor * Easy interface with a 4-bit or 8-bit MPU * Display character pattern: 5
7 dots format: 192 kinds, 5
10 dots format: 32kinds * The special character pattern can be programmable by Character Generator RAM directly. * A customer character pattern can be programmable by mask option (KS0068B-00; Standard type) KS0068B-00 English, Japanese Numberal * Automatic power on reset function. * It can drive a maximum 80 characters by using the kS0065B or KS0063B, KS0068B externally. * It is possible to read both Character Generator and Display Data RAM from MPU.
FEATURES
* Internal Memory - Character Generator ROM: 8320bits - Character Generator RAM: 512 bits - Display Data RAM: 80
8bits for 80 digits. * Power Supply Voltage; +5Va10%, +3Va10% * Supply voltage for display: 0~-5V(V5) * CMOS process * 1/8 duty, 1/11 duty or 1/16 duty: selectable (1/8 duty; 5
7 dots format 1 line, 1/11 duly; 5 x 10 dots format I line, 1/16 duty: 5
7 dots format 2 line) * 100 QFP or bare chip available.
KS0068B
16COM/60SEG DRIVER & CONTROLLER FOR DOT MATRIX LCD
BLOCK DIAGRAM
Power supply for LCD Drive V1 V2 V3 V4 V5 5 5 Parallel/Serial Data conversion Circuit
Busy Flag
Charater Generator ROM ( CG ROM ) 8320 bits
Character Generator RAM ( CG RAM ) 512 bits
Cursor Blink Control Circuit segment
DB0 ~ DB3 DB4 ~ DB 7
4 4 8 Input Output Buffer Data Register ( DR ) 8 7 Display 8 Instruction Register ( IR ) 8 Instruction Decoder ( ID ) 7 7 Data RAM ( DD RAM ) 80!8 bits 8 8 60 - bit Shift Register 60 60 - bit Latch Circuit 60
signal ( S1 - S60 ) Segment 60 Signal Driver
R/W RS E
D
7
Address Counter ( AC ) 7
7 common signal ( C 1 - C16 )
16 - bit Shift Register
16
Common Signal Driver
16
OSC 1 OSC 2
Timing Generation Circuit
CLK1 CLK2 M
VDD GND
Fig. 1. KS0068 functional block diagram.
KS0068B
16COM/60SEG DRIVER & CONTROLLER FOR DOT MATRIX LCD
PIN CONFIGURATION
C 16
C 15
C 14
C 13
C 12
C 11
C 10
S 47
S 48
S 49
S 50
S 51
S 52
S 53
S 54
S 55
S 56
S 57
S 58
S 59
S 60
C9
C8
C7
C6
C5
C4
C3
C2 52
80 S 46 S 45 S 44 S 43 S 42 S 41 S 40 S 39 S 38 S 37 S 36 S 35 S 34 S 33 S 32 S 31 S 30 S 29 S 28 S 27 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100
79
78
77
76
75
74
73
72
71
70
69
68
67
66
65
64
63
62
61
60
59
58
57
56
55
54
53
51 50 49 48 47 46 45 44 43 42 DB 7 DB 6 DB 5 DB 4 DB 3 DB 2 DB 1 DB 0 V DD E R/W RS D M CLK 2 CLK 1 V5 V4 V3 V2
KS0068B
KS0068
C1
41 40 39 38 37 36 35 34 33 32 31
1 S26
2 S25
3 S24
4 S23
5 S22
6 S21
7 S20
8 S19
9 S18
10 S17
11 S16
12 S15
13 S14
14 S13
15 S12
16 S11
17 S10
18 S9
19 S8
20 S7
21 S6
22 S5
23 S4
24 S3
25 S2
26 S1
27 VSS
28 OSC2
29 OSC1
30 V1
Fig2. 100QFP Top View
Fig2. 100QFP Top View
KS0068B
16COM/60SEG DRIVER & CONTROLLER FOR DOT MATRIX LCD
PIN DESCRIPTION
PIN(No). VDD(42) VSS(GND) (27) V1-V5(30-34) S1-S60 (1-26, 67-100) C1-C16 (51-66) OSC1, OSC2 (29) (28) INPUT/OUTPUT Power NAME DESCRIPTION Operating Voltage for logical circuit (2.7V ~ 5.5V) 0V (GND) Negative Supply Bias voltage level for LCD driving Voltage Segment output Segent signal output for LCD driving Common output Oscillator Common signal output for LCD driving Both pin connected to Rf resistor or ceramic resonator for internal oscillator circuit. In case of external frequency use only, the frequency is input to OSC1 terminal. Clock output terminal for the serially transfered data to be latched to the driver. Clock output terminal used when D terminal data output shifts the inside of the driver. The alternating signal to convert LCD drive waveform to AC Character pattern data, which is corresponding to each common signal, is supplied to driver serially. High Low E(41) R/W(40) Input Enable Read/Write Selection Non selection INTERFACE Power Supply
Output Output Input (OSC1) Output (OSC2)
LCD LCD Resistor or Ceramic Resonator KS0065B or KS0063B
CLK1 (35)
Output
Data latch clock
CLK2 (36) M (37)
Data shift clock Alternated signal for LCD driver output Display data interface
D (38)
Start enable signal to read or write the data R/W signal input is used to select the read/write mode High Low Read mode Write mode
MPU
RS (39)
Register select
register selection input High Low Data register (for read and write) Instruction register (for write), Busy flag, address counter (for read)
DB0-DB7 (43-50)
Input/Output
Data interface
Used for data transfer between the MPU and KS0068. These terminals are for data bus with bidirectional three-state. Initial 4 bit (DB0-DB3) are not used during 4-bit operation (DB7 can be used as a busy flag)
KS0068B
16COM/60SEG DRIVER & CONTROLLER FOR DOT MATRIX LCD
Internal logic of input/output terminal
Input/Output Input Logic diagram No Pull up Applicable pin E
with pull up
RS, R/W
Output
CLK1, CLK2 M,D
Input Output
DB0-DB7
KS0068B
16COM/60SEG DRIVER & CONTROLLER FOR DOT MATRIX LCD
MAXIMUM ABSOLUTE LIMIT (Ta=25I)
Characteristic Operating Voltage Driver Supply Voltage Input Voltage Power Dissipation Operating Temperature Storage Temperature Symbol VDD VLCD VIN PD T OPR T STG Value -0.3~+7.0 VDD-11.5~VDD+0.3 -0.3 ~ VDD+0.3 500 -30~+85 -55~+125
3 4 5
Unit V V V mW
~ Voltage greater than above may damage to the circuit (VDD
V V V V V )
1 2
I I
ELECTRICAL CHARACTERISTICS
DC Characteristics (VDD=+5Va10%, VSS=0V, Ta=-30 ~ +85I)
Characteristic Operating Voltage Operating Current (*1) Symbol VDD IDD1 IDD2 Test condition Ceramic resonator fosc=250KHz Resistor oscillation external clock operation fosc=270KHz IOH=-0.205mA IOL=1.2mA IO=-40A IO=40A IO=a0.1mA VIN=0 or VDD VDD=5V (test pull up R) Min 4.5 Typ 0.65 0.45 Max 5.5 0.9 0.7 Unit V mA Applicable Pin
Input Voltage 1 Input Voltage 2
High Low High Low High Low High Low COM SEG
VIH1 VIL1 VIH2 VIL2 VOH1 VOL1 VOH2 VOL2 VdCOM VdSEG ILKG IIN fEC duty tR tF fOSC1 fOSC2
Output Voltage 1 Output Voltage 2
2.2 -0.3 VDD -1.0 -0.2 2.4 0.9VDD -1 -50 125 45 190 245
-125 250 50 270 250
VDD 0.6 VDD 1.0 0.4 0.1VDD 1 1 1 -250 350 55 0.2 0.2 350 255
V
E, DB0-DB7, R/W, RS OSC1
DB0-DB7 CLK1, CLK2, M, D C1-C16 S1-S60 E RS,R/W OSC1
Voltage Drop (*2)
Input Leakage Current Input Low Current External Clock Frequency(*3) Duty Rise time Fall time Internal Clock Frequency(*3) Ceramic Resonator OSC Frequency (*3) LCD driving voltage(*4)
A
KHz %
Rf=91KKHz

OSC1, OSC2
VLCD1 VDD-V5 1/5 bias 3.0 10.0 V V1-V5 VLCD2 1/6 bias 3.0 10.0 Note: *1) Applies to the current value flown in terminal VDD when power is input as follows; VDD=5V, GND=0V, V1=3.4V, V2=1.8V, V3=0.2V, V4=-1.4V and V5=-3V. *2) Applied to the voltage drop occuring from terminals VDD, V1, V4 and V5 to each common terminal (C1-C16) when 0.1mA is flown in or out to and from all COM and SEG terminals, and also to voltage drop occuring from terminals VDD, V2, V3 and V5 to each SEG terminal (S1-S60). When the output level is at VDD, V1 or V2 level, 0.1mA is flown out, while 0.1mA flow in when the output level is at V3, V4 or V5 level. This occurs when 5V or -5V is input to VDD, V1 and V3 or to V2, V4, and V5 respectively.
KS0068B
16COM/60SEG DRIVER & CONTROLLER FOR DOT MATRIX LCD
DC Characteristics (VDD=+3Va10%, VSS=0V, T a=-30 ~ +85I) Characteristic Symbol Test condition Min Typ Max Unit Applicable Pin Operating Voltage VDD 2.7 3.0 3.3 V Operating Current (*1) IDD1 Ceramic resonator 0.3 0.5 mA fosc=250KHz IDD2 Resistor oscillation 0.17 0.3 external clock operation fosc=270KHz Input Voltage 1 High VIH1 1.9 VDD V E, DB0-DB7, Low VIL1 -0.3 0.4 R/W, RS Input Voltage 2 High VIH2 0.7VDD VDD OSC1 Low VIL2 0.2VDD Output Voltage 1 High VOH1 IOH=-0.1mA 2.0 DB0-DB7 Low VOL1 IOL=0.1mA 0.4 Output Voltage 2 High VOH2 CLK1, CLK2, 0.8VDD IO=-40A Low VOL2 M, D 0.2VDD IO=40A Voltage Drop (*2) COM VdCOM 1 C1-C16 IO=a0.05mA SEG VdSEG 1.5 S1-S60 Input leakage current ILKG VIN=0 or VDD -1 1 E Input Low Current IIN VDD=3V (test pull up R) -10 -50 -120 RS,R/W External Clock Frequency fEC 125 250 350 KHz OSC1 (*3) Duty duty 45 50 55 % Rise time tR 0.2 Fall time tF 0.2 Internal clock Frequency(*3) fOSC 190 270 350 KHz OSC1, OSC2 Rf=75KA

KS0068B
16COM/60SEG DRIVER & CONTROLLER FOR DOT MATRIX LCD
*3) Oscillator circuit Resistor circuit External clock cirucit
*4) Input the voltage listed in the table below to V1-V5 Duty Power supply V1 V2 V3 V4 V5 Bias 1/8, 1/11 1/4 VDD-VLCD/4 VDD-VLCD/2 VDD-VLCD/2 VDD-3VLCD/4 VDD-VLCD 1/16 1/5 VDD-VLCD/5 VDD-2VLCD/5 VDD-3VLCD/5 VDD-4VLCD/5 VDD-VLCD
~VLCD is the LCD driving voltage, refer to the initial set of the instruction code.
KS0068B
16COM/60SEG DRIVER & CONTROLLER FOR DOT MATRIX LCD
AC Characteristics (VDD=5V 10%, VSS=0V, Ta=-30 ~ +85)
(1) Write mode (Writing data from Micom to KS0068B) Characteristic Symbol Min E Cycle Time tc 500 E Rise Time tR E Fall Time tF E Pulse Width (High, Low) tW 220 R/W And RS Set-Up Time tSU1 40 R/W And RS Hold Time tH1 10 Data Set-Up Time tSU2 60 Data Hold Time tH2 10 Typ Max 25 25 Unit ns ns ns ns ns ns ns ns Test pin E E E E R/W, RS R/W, RS DB0~DB7 DB0~DB7
RS
VIH1 VIL1 tSU1
VIH1 VIL1 tH1
R/W VIL1 tw VIH1 VIL1 tR VIH1 VIL1 tSU2 tF tH2 VIL1 tH1 VIL1
E
DB0 - DB7
VIH1 VIL1
Valid Data tC
VIH1 VIL1
KS0068B
16COM/60SEG DRIVER & CONTROLLER FOR DOT MATRIX LCD
(2) Read mode (Reading data from KS0068B to Micom) Characteristic Symbol Min E Cycle Time tc 500 E Rise Time tR E Fall Time tF E Pulse Width (High, Low) tW 220 R/W And RS Set-Up Time tSU 40 R/W And RS Hold Time tH 10 Data Output Delay Time tD Data Hold Time tDH 20
Typ -
Max 25 25 120 -
Unit ns ns ns ns ns ns ns ns
Test pin E E E E R/W, RS R/W, RS DB0~DB7 DB0~DB7
RS
V IH 1 V IL1 tSU
V IH 1 V IL1 tH
R/W
V IL1 tw tF tH
V IH 1 E V IL1 tR tD DB 0 - DB 7 V IH 1 V IL1 t DH V IH 1 V IL1 V IL1 V IL1
V alid Da ta tC
KS0068B
16COM/60SEG DRIVER & CONTROLLER FOR DOT MATRIX LCD
(3) Interface mode with KS0065B, KS0063B Characteristic Clock Pulse Width High Clock Pulse Width Low Data Set-Up Time Data Hold Time Clock Set-Up Time M Delay Time Symbol tWCKH tWCKL tSU tDH tCSU tDM Min 800 800 300 300 500 -1000 Typ Max 1000 Unit ns ns ns ns ns ns Test pin CLK CLK D D CLK M
0 .9 V C LK 1
DD
0 .9 V
DD
tW C LK 2 0 .1 V
DD
CKH
tW
CKH
tC S U 0 .9 V 0 .9 V
DD DD
0 .1 V tC S U
DD
0 .1 V tW
CKL
DD
D
0 .9 V D D 0 .1 V D D tS U
0 .9 V D D 0 .1 V D D tD H
M
0 .9 V
DD
tD M
KS0068B
16COM/60SEG DRIVER & CONTROLLER FOR DOT MATRIX LCD
AC Characteristics (VDD=3V 10%, VSS=0V, Ta=-30 ~ +85)
(1) Write mode (Writing data from Micon to KS0068B) Characteristic Symbol Min E Cycle Time tc 1400 E Rise Time tR E Fall Time tF E Pulse Width (High, Low) tW 400 R/W And RS Set-Up Time tSU1 60 R/W And RS Hold Time tH1 20 Data Set-Up Time tSU2 140 Data Hold Time tH2 10 Typ Max 25 25 Unit ns ns ns ns ns ns ns ns Test pin E E E E R/W, RS R/W, RS DB0~DB7 DB0~DB7
(2) Read mode (Reading data from KS0068B to Micom) Characteristic E Cycle Time E Rise Time E Fall Time E Pulse Width (High, Low) R/W And RS Set-Up Time R/W And RS Hold Time Data Output Delay Time Data Hold Time Symbol tc tR tF tW tSU tH tD tDH Min 1400 400 60 20 5 Typ Max 25 25 360 Unit ns ns ns ns ns ns ns ns Test pin E E E E R/W, RS R/W, RS DB0~DB7 DB0~DB7
(3) Interface mode with KS0065B, KS0063B Characteristic Symbol Min Clock Pulse Width High tWCKH 800 Clock Pulse Width Low tWCKL 800 Data Set-Up Time tSU 300 Data Hold Time tDH 300 Clock Set-Up Time tCSU 500 M Delay Time tDM -1000
Typ -
Max 1000
Unit ns ns ns ns ns ns
Test pin CLK CLK D D CLK M
KS0068B
16COM/60SEG DRIVER & CONTROLLER FOR DOT MATRIX LCD
CONTROL and DISPLAY COMMAND
Command DISPLAY CLEAR RETURN HOME ENTRY MODE SET RS R/W DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0 L L L L L L L L L L L L L L L L L L L L L L L H L H I/D H X SH Excution Remark time (fosc=250KHz) 1.64ms 1.64ms cursor move to first digit *I/D; set cursor move direction 40 H L Increase Decrease
I/D
*SH: Specifies shift of display SH H L DISPLAY ON/OFF L L L L L L H D C B 40 *Display D *Cursor C H L Cursor on Cursor off H L Display on Display off display is shifted display is not shifted
*Blinking B SHIFT L L L L L H S/C R/L X X 40 SC H L H L SET FUNCTION L L L L H DL N F X X 40 DL L H L H L H H L Blinking on Blinking off Display shift Cursor move Right shift Left shift
R/L
8 bits interface 4 bits interface 2 line display 1 line display 5
10 dots 5
7 dots
N
F
Table 1.
KS0068B
16COM/60SEG DRIVER & CONTROLLER FOR DOT MATRIX LCD
CONTROL and DISPLAY COMMAND(continued)
Command SET CG RAM ADDRESS SET DD RAM ADDRESS READ BUSY FLAG & ADDRESS RS R/W DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0 L L L L L H L H BF H Excution Remark time (fosc=250KHz) CG RAM address CG RAM Data is sent and 40 (corresponds to cursor address) received after this setting DD RAM Data is sent and DD RAM address 40 recevied after this setting Address Counter used for 0 B FF H Busy Both DD & CG RAM address L Ready - Reads BF indication internal operating is being performed. - reads address counter contents Write data into DD or CGRAM Read data from DD or CGRAM X : Don't care
WRITE DATA READ DATA
H H
L H
Write Data Read Data
46 46
KS0068B
16COM/60SEG DRIVER & CONTROLLER FOR DOT MATRIX LCD
APPLICATION INFORMATION ACCORDING TO LCD PANEL
1) LCD Pandel: 12 character
1 line, character format; 5
7 dots + 1 cursor line (1/4 bias, 1/8 duty)
~ ~ ~ ~ ~~ ~ ~ ~ ~ ~ ~ ~~ ~ ~ C1
C8 S1
KS0068
S 60
2) LCD Panel: 12 character
1 line, character format; 5
10 dots + 1 cursor line (1/4 bias, 1/11 duty)
C1
C11 KS0068 S1
S60
KS0068B
16COM/60SEG DRIVER & CONTROLLER FOR DOT MATRIX LCD
3) LCD Panel : 12 character
2 line character format; 5
7 dots + 1 cursor line (1/5 bias, 1/16 duty)
C1
C8 C9
K S 0 0 68
C 16
S1
S 60
4) LCD Panel : 24 character
1 line, character format; 5
7 dots + 1 dots + 1 cursor line (1/5 bias, 1/16 duty)
C1
C8
KS0068
S1
S60 C9
C16
KS0068B
16COM/60SEG DRIVER & CONTROLLER FOR DOT MATRIX LCD
5) LCD Panel : 6 character 2 line character format; 5 7 dots + 1 cursor line (1/4 bias, 1/8 duty)
S1

S30
C1
C8 KS0068
S31
S60
BIAS VOLTAGE DIVIDE CIRCUIT
KS0068
KS0068
VDD VDD
V1
V2
V3
V4
V5 VDD
VDD
V1
V2
V3
V4
V5
R
R
R
R
R
R
R
R
R
APPLICATION CIRCUIT
( 1/4 bias, 1/8 or 1/11 duty )
-5V or GND
( 1/5 bias, 1/16 duty )
-5V or GND
16COM/60SEG DRIVER & CONTROLLER FOR DOT MATRIX LCD
C1 ~ C16
LCD Panel
S1 ~ S60 DL2 DR1 KS0065B
SC1 ~ SC40
SC1 ~ SC40 DL2 DR1 KS0065B DL1 DR2 CL1 CL2 FCS SHL1 DR2 CL1 CL2 SHL2 M VSS VDD V6 V5 V4 V3 V2 V1 VEE
SC1 ~ SC40 DL2 DR1 DL1 FCS SHL1 KS0065B DR2 CL1 CL2 SHL2 M V SS VDD V6 V5 V4 V3 V2 V1 VEE
D FCS OSC1 SHL1
DL1
OSC2
SHL2 M VSS VDD V6 V5 V4 V3 V2 V1 VEE
KS0068
VSS M CLK1 CLK2 VDD V1 V2
VDD
V2 V3 V4 DB0 ~ DB7 V5 V3 V4 V5
APPLICATION CIRCUIT
KS0068B
To MPU
GND or Other voltage
VLCD ( 1/5 bias )
V1
When KS0065B is externally connected to the KS0068, you can increase the number of display digits up to 80 characters.
KS0068B
16COM/60SEG DRIVER & CONTROLLER FOR DOT MATRIX LCD
PAD DIAGRAM
100 1 2 3 4 5 6 7 8 9 10 11 12 13
99
98
97
96
95
94
93
92
91
90
89
88
87
86
85
84
83
82
81
80 79 78 77 76 75 74 73 72 71 70 69 68
KS0068B
Y
(0,0)
14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29
X
67 66 65 64 63
! 4980 PAD SIZE : 100 ! 100 UNIT : m
CHIP SIZE : 5770
62 61 60 59 58 57 56 55 54 53 52 51
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
* KS0068B Marking : easy to find the PAD No.72,81
KS0068B
PAD LOCATION
PAD NUMBER 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 PAD NAME SEG26 SEG25 SEG24 SEG23 SEG22 SEG21 SEG20 SEG19 SEG18 SEG17 SEG16 SEG15 SEG14 SEG13 SEG12 SEG11 SEG10 SEG9 SEG8 SEG7 SEG6 SEG5 SEG4 SEG3 SEG2 SEG1 VSS OSC2 OSC1 V1 V2 V3 V4 V5
16COM/60SEG DRIVER & CONTROLLER FOR DOT MATRIX LCD
UNIT (I m) COORDINATE X Y 1686 1560 1436 1310 1186 1060 936 810 686 560 436 310 186 60 -64 -190 -314 -440 -564 -690 -814 -940 -1064 -1190 -1314 -1440 -1702 -1868 -1994 -2358 -2358 -2358 -2358 -2358 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 CLK1 CLK2 M D RS R/W E VDD DB0 DB1 DB2 DB3 DB4 DB5 DB6 DB7 COM1 COM2 COM3 COM4 COM5 COM6 COM7 COM8 COM9 COM10 COM11 COM12 COM13 COM14 COM15 COM16 SEG60 SEG59 PAD NUMBER PAD NAME COORDINATE X -453 -328 -203 -78 47 172 297 422 547 672 797 922 1047 1172 1297 1422 1684 1684 1684 1684 1684 1684 1684 1684 1684 1684 1684 1684 1684 1684 1684 1684 1684 1684 Y -2358 -2358 -2358 -2358 -2358 -2358 -2358 -2358 -2358 -2358 -2358 -2358 -2358 -2358 -2358 -2358 -1814 -1690 -1564 -1440 -1314 -1190 -1064 -940 -814 -690 -564 -440 -314 -190 -64 60 186 310 PAD NUMBER 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 PAD NAME SEG58 SEG57 SEG56 SEG55 SEG54 SEG53 SEG52 SEG51 SEG50 SEG49 SEG48 SEG47 SEG46 SEG45 SEG44 SEG43 SEG42 SEG41 SEG40 SEG39 SEG38 SEG37 SEG36 SEG35 SEG34 SEG33 SEG32 SEG31 SEG30 SEG29 SEG28 SEG27 COORDINATE X 1684 1684 1684 1684 1684 1684 1684 1684 1684 1684 1684 1249 1124 999 874 749 624 499 374 249 124 -1 -126 -251 -376 -501 -626 -751 -876 -1001 -1126 -1251 Y 436 560 686 810 936 1060 1186 1310 1436 1560 1686 2358 2358 2358 2358 2358 2358 2358 2358 2358 2358 2358 2358 2358 2358 2358 2358 2358 2358 2358 2358 2358
I
-1684 -1684 -1684 -1684 -1684 -1684 -1684 -1684 -1684 -1684 -1684 -1684 -1684 -1684 -1684 -1684 -1684 -1684 -1684 -1684 -1684 -1684 -1684 -1684 -1684 -1684 -1684 -1684 -1684 -1078 -953 -828 -703 -578
KS0068B
16COM/60SEG DRIVER & CONTROLLER FOR DOT MATRIX LCD
Standard Character Pattern (KS0068B-00)

▲Up To Search▲

Price & Availability of KS0068B

	To Download KS0068B Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .